3/4"

Marine Products

Built with Volusion

Visit our location!
150 Riberia Street
St. Augustine, FL 32085
Phone: (904) 829-2271

Check us out on
Facebook!

Marsupco

Home > Hose Diameter > 3/4"

Sort By:

Page of 2

Trident A2 Fuel Fill Hose #327 (cut)

per foot

Trident A2 Fuel Fill Hose for gasoline fill hose (including ethanol blends) and diesel (including bio diesel blends). The #327 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, & USCG Type A2; and is NMMA Type accepted, CE certified and Lloyds Registry Type Approved. This hose is built with the best fuel, fire and age resistant formulation. Provides extraordinary resistance to aging, fire, heat, cold, and the ozone. Also provides excellent bend-ability.

Trident Barrier Lined A1-15 Fuel Hose #365 (cut)

Trident Barrier Lined A1-15 Fuel Hose #365 (cut)

per foot

Trident Barrier Lined A1-15 Fuel Hose for both gasoline (including ethanol blends) and diesel (including bio diesel blends). The #365 series exceeds ABYC H-24 & H-33, SAE J1527, ISO 7840, USCG Type A1-15; CARB Executive Order and EPA Certified low permeation Type A1-15; and is NMMA Type Accepted & CE certified. This hose is built with the best fuel, fire and age resistant formulation and a unique "Barrier Liner" on inside surface of the tube, so fuel is not in direct contact with rubber. Provides extraordinary resistance to fuel permeation, aging, and also to fire, heat, cold, and the ozone. Also provides excellent bend-ability.

Trident Flex Marine Wet Exhaust Water Hose #250/100 (cut)

Trident Flex Marine Wet Exhaust Water Hose #250/100 (cut)

per foot

Premium wet exhaust hose for longer bent connections. In smaller I.D.'s for engine intake, critical water, drain, scupper bilge and sanitation uses. Extra heavy tube and cover with helix between 2 ply reinforcement provides excellent flexibility and bend radius. Resists heat, ozone, exhaust, sani chemicals, panting and collapse. Exceeds New (SAE J2006, ABYC and NMMA) Stds. Black High Temp EDPM Rubber 250°F (121°C).

Trident Ply Marine Wet Exhaust Water Hose #200/110 (cut)

Trident Ply Marine Wet Exhaust Water Hose #200/110 (cut)

per foot

Premium marine wet exhaust hose for short, straight connections. In smaller I.D.'s for critical engine coolant & circulation, heat exchanger and discharge uses. Extra heavy tube and cover with 2 to 6 ply reinforcement resists heat, aging, ozone, exhaust and sani chemicals. Exceeds New (SAE J2006, ABYC and NMMA) Stds. Black High Temp EDPM Rubber 250°F (121°C).

Trident Blue Corra-Sil Marine Wet Exhaust & Water Hose #252V (cut)

Trident Blue Corra-Sil Marine Wet Exhaust & Water Hose #252V (cut)

per foot

Ultimate quality Silicone Marine Exhaust & Water hose. #252V Blue Very Hi Temp. [4 to 6 ply polyester reinforcement 350°F (177°C)] dramatically exceeds all standards and lasts up to 6 times longer than black rubber. (SAE J2006, ABYC and NMMA) Stds. See Marine Wet Exhaust Systems Catalog. ISO 13363 Std. Pending.

Trident Silicone & Rubber Heater Hose #131V (cut)

Trident Silicone & Rubber Heater Hose #131V (cut)

per foot

Ultimate Silicone Heater Hose- Very Hi Temp Blue with Red Tube provides much greater temperature range and service life (up to 6 times longer) than standard EDPM rubber #130 Heater Hose. 2 spiral polyester reinforced with similiar working pressure for engine coolant water, A/C and other mid-pressure water applications. #131V (VHT-Blue): 45 to 75PSI (0.31 to 0.52Mpa) WP 350°F (177°C) SAE J20R3, Class 1 & J20P3.

Trident HD Rubber Heater Hose #132 (cut)

Trident HD Rubber Heater Hose #132 (cut)

per foot

Trident X HD Water/Heater Hose #134 (cut)

Trident X HD Water/Heater Hose #134 (cut)

per foot

Cost effective, Hi Temp, EPDM rubber, polyester reinforced and exceeds SAE J20R3. Both are resistant to coolants, ozone, cold & heat; and serve a variety of boat and plant pressurized applications (water & air delivery).
#134: 4 spiral, heavy wall and better bend radius and working pressure - 300PSI (2.1Mpa) WP. Operating temperature -40° to 212°F (-40° to 100°C). #134 serves below water line intake and discharge applications (A/C, Eng, Sani) etc.

Trident Clear PVC Tubing #150 (cut)

per foot

Non-toxic FDA compounded PVC for many unpressurized, cool water uses like fresh water drain and vent lines. Operating tempratures (+20° - +150° F). NOT RECOMMENDED FOR BELOW-THE WATERLINE THRU-HULL CONNECTIONS.

Trident Bilge Hose #120/121 (cut)

per foot

Extremely flexible and tough corrugated polyethylene hose for bilge intake and discharge. Cuffed every foot for clamping. Resists oily bilge and sea water.
NOT RECOMMENDED FOR BELOW WATERLINE THRU-HULL CONNECTIONS.
Operating tempratures -40° to +200°F (-40° to +93°C).